Inspection & Engineering - ICorr Level 2

ISO and other International Standards

32 Lessons
LESSONS

Lesson 1 - BS EN ISO 8503-2

BS EN ISO 8503-2 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective


The objective to this training unit is to give an overview of the BS EN ISO 8503-2 which is titled "Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast cleaned steel substrates.


Part 2: Method for the grading of abrasive blast cleaned steel – Comparator procedure.

This standard is widely used in the protective coatings industry.

Lesson 2 - BS EN ISO 8503-3

BS EN ISO 8503-3 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8503-3 which is titled "Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast cleaned steel substrates.


Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile – Focusing microscope procedure.

Lesson 3 - BS EN ISO 8503-4

BS EN ISO 8503-4 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8503-4 which is titled "Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast cleaned steel substrates.


Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile – Stylus instrument procedure.

Lesson 4 - BS EN ISO 8503-5

BS EN ISO 8503-5 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8503-5 which is titled "Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast cleaned steel substrates.

Part 5: Replica tape method for the determination of the surface profile.

Lesson 5 - BS EN ISO 8504-1

BS EN ISO 8504-1 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8504-1 which is titled "Preparation of steel substrates before application of paints and related products – Surface preparation methods


Part 1: General principles

Lesson 6 - BS EN ISO 8504-2

BS EN ISO 8504-2 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8504-2 which is titled "Preparation of steel substrates before application of paints and related products – Surface preparation methods

Part 2: Abrasive blast cleaning

Lesson 7 - BS EN ISO 8504-3

BS EN ISO 8504-3 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8504-3 which is titled "Preparation of steel substrates before application of paints and related products – Surface preparation methods


Part 3: Hand and Power Tool Cleaning.

Lesson 8 - BS EN ISO 2409 (BS3900-E6)

BS EN ISO 2409 (BS3900-E6) ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

This training unit gives a review of the ISO 2409 and BS3900-E6 Standard.

The standard is titled ‘Paints and Varnish – Cross Cut Test.

Lesson 9 - ISO Miscellaneous

ISO MISCELLANEOUS ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a brief introduction to the various ISO Standards used in the protective coatings industry.

The list is not exhaustive as there are other coating Standards within the ISO range.

The Standards are generally specified within the painting specification for specific contracts.

The full standards can be purchased via the internet

Lesson 10 - SSPC VIS 2

SSPC VIS 2 SSPC STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a full and comprehensive review of the SSPC-VIS-2 standard titled ‘Standard Method of Evaluating Degree of Rusting on Painted Steel Surfaces’.

On completion of this training unit the student should be able to use the standard for inspection duties.

Lesson 11 - SSPC - PA1

SSPC - PA1 SSPC STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this unit is to give an overview on SSPC PA 1: Shop, Field and Maintenance Painting of Steel.

The specification contains 14 sections and each one is briefly described in the slides that follow.

Lesson 12 - SSPC - PA2

SSPC - PA2 SSPC STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The Objective to this training unit is to give an overview of the SSPC – PA2 standard which is produced by the SSPC The Society for Protective Coatings.

The Standard is titled ‘measurement of dry film thickness with gauges’

The standard is widely used in coating specifications.

This unit is not a comprehensive review of the standard so the user should ensure that a copy of the standard is available and understood before use.

Lesson 13 - SSPC Miscellaneous

SSPC MISCELLANEOUS SSPC STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this unit is to cover any miscellaneous standards relating to SSPC: The Society for Protective Coatings.

The list is not exhaustive as there are many other coating Standards within the SSPC range.

Lesson 14 - ASTM D 4541

ASTM D 4541 ASTM STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of ASTM D4541 which is the test method for determining the pull-off strength of coatings using a portable adhesion tester.

The test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying a force to a dolly attached to the coating surface by an adhesive.

Lesson 15 - ASTM D 6677

ASTM D 6677 ASTM STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a overview of the ASTM D6677 which is the test method for ‘Evaluating Adhesion by Knife’.

This test method is a quick and easy way to measure adhesion in a laboratory or in the field.

Although the test method is relatively straightforward with little equipment necessary, it should only be conducted by experienced personnel.

Lesson 16 - ASTM D 3359

ASTM D 3359 ASTM STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a overview of the ASTM D3359 which is the test method for measuring adhesion by tape test.

The test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film.

Lesson 17 - ASTM D 4417

ASTM D 4417 ASTM STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a overview of the ASTM D4417 which is titled ‘The Standard for Field Measurement of Surface Profile of Blast Cleaned Steel’.

The full standard can be purchased via the internet.

Lesson 18 - ASTM Miscellaneous Standards

ASTM MISCELLANEOUS STANDARDS ASTM STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a brief introduction to the various ASTM Standards used in the protective coatings industry.

The list is not exhaustive as there are other coating Standards within the ASTM range.

The Standards are generally specified within the painting specification for specific contracts.

The full standards can be purchased via the internet.

Lesson 19 - NORSOK M-501

NORSOK M-501 NORSOK STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the NORSOK Standard M-501 entitled, Surface preparation and protective coating, which gives the requirements for the selection of coating materials, surface preparation, application procedures and inspection for protective coatings to be applied during the construction and installation of offshore installations and associated facilities.

Lesson 20 - EN ISO 12944 (Parts 1-9)

EN ISO 12944 (PARTS 1-8) ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective:

The objective of this training unit is to give an understanding of the EN ISO Standard 12944 Paints and Varnishes – Corrosion Protection of Steel Structures by Protective Paint Systems Parts 1-8.

This standard is widely used in the protective coatings industry.

Lesson 21 - EN ISO 4624

EN ISO 4624 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective:

The objective of this training unit is to give an understanding of the EN ISO Standard 4624

This standard is widely used in the protective coatings industry.

Lesson 22 - EN ISO 4628 (Parts 1-6)

EN ISO 4628 (PARTS 1-6) ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective:

The objective of this training unit is to give an overview of the EN ISO 4628 Parts 1 to 6.

Paints and varnishes – evaluation of degradation of paint coatings.  Designation of intensity, quantity and size of common types of defects.

Lesson 23 - BS EN ISO 8502 Part 2

BS EN ISO 8502 PART 2 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-2.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 2: Laboratory determination of chloride on cleaned surfaces.

Lesson 24 - BS EN ISO 8502 Part 3

BS EN ISO 8502 PART 3 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-3.

The document is titled ‘Preparation of steel substrates before application of paints and related products – tests for the assessment of surface cleanliness – Part 3: Assessment of dust on steel surfaces prepared for painting. (pressure-sensitive Tape method).

Lesson 25 - BS EN ISO 8502 Part 4

BS EN ISO 8502 PART 4 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-4.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 4: Guidance on the estimation of the probability of condensation prior to paint application.

Lesson 26 - BS EN ISO 8502 Part 5

BS EN ISO 8502 PART 5 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-5.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 5: Measurement of chloride on steel surfaces prepared for painting (ion detection tube method).

Lesson 27 - BS EN ISO 8502 Part 6

BS EN ISO 8502 PART 6 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-6.

The document is titled: ‘Preparation of steel substrates before application of paints and related products – tests for assessment of surface cleanliness – Part 6: Extraction of soluble contaminants for analysis – The Bresle Method’.

Lesson 28 - BS EN ISO 8502 Part 8

BS EN ISO 8502 PART 8 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-8.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 8: Field method for the refractometric determination of moisture.

Lesson 29 - BS EN ISO 8502 Part 9

BS EN ISO 8502 PART 9 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-9.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 9: Field method for the conductometric determination of water-soluble salts.

Lesson 30 - BS EN ISO 8502 Part 11

BS EN ISO 8502 PART 11 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-11.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 11: Field method for the turbidimetric determination of water-soluble sulphate.

Lesson 31 - BS EN ISO 8502 Part 12

BS EN ISO 8502 PART 12 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective of this training unit is to give a thorough overview of the ISO 8502-12.

The document is titled ‘Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 12: Field method for the titrimetric determination of water-soluble ferrous ions.

Lesson 32 - BS EN ISO 8503-1

BS EN ISO 8503-1 ISO STANDARDS ISO AND OTHER INTERNATIONAL STANDARDS

Objective

The objective to this training unit is to give an overview of the BS EN ISO 8503-1 which is titled

"Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast cleaned steel substrates.

Part 1: specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast cleaned surfaces."

This standard is widely used in the protective coatings industry.